Sheet Metal Bend Allowance Calculator

Calculate the exact arc length along the neutral axis of a sheet metal bend to determine the material consumed by the bend curvature.

Calculation Results

Bend Allowance (BA)
5.9690 mm
Shifted Neutral Axis Radius (Rn) 3.8000 mm
Neutral Axis Offset (t = K × T) 0.8000 mm
Equivalent Bend Deduction (for 90°) 4.0310 mm
Neutral Axis Geometry DIN 6935
Center R Neutral Axis (BA) Rn = R + K×T T Outer: Tension (Stretched) Inner: Compression
DIN 6935 Equation: BA = (π / 180) × A × (R + K × T)

How to Use the Bend Allowance Calculator

01

Select Material Standard

Pick your alloy from the preset menu (Mild Steel, 304 Stainless, Aluminum 6061/5052, Copper) to automatically load empirical K-factor values.

02

Input Gauge & Tooling Radius

Enter actual caliper thickness (T) and the inside bend radius (R) formed by your press brake punch nose or natural air bend opening.

03

Enter Bend Angle

Specify the degrees of rotation from flat (90° for square bends, 45° for obtuse angles, or up to 175° for sharp acute bends).

04

Derive Flat Blank Size

Add the calculated Bend Allowance directly to the straight tangent leg segments of your part: L_flat = L_straight1 + L_straight2 + BA.

Neutral Axis & Strain Distribution

During bending, material outside the neutral axis undergoes plastic tension, while material inside the neutral axis undergoes plastic compression. Because metals yield more easily in compression than tension during bending, the neutral axis shifts inward toward the punch radius.

Bend Allowance Formula (DIN 6935):
BA = (π / 180) × A × (R + K × T)
BA = Bend Allowance (arc length along neutral fiber)
A = Bend Angle in degrees
R = Inside bend radius
K = K-Factor (neutral axis offset ratio, typically 0.33 – 0.50)
T = Material thickness

Worked Example & Shop Tips

Example Problem: A 90° bend in 2.0 mm mild steel with an inside radius of 3.0 mm and K = 0.40.

  • Offset (t): K × T = 0.40 × 2.0 = 0.80 mm
  • Neutral Radius (Rn): 3.0 + 0.80 = 3.80 mm
  • Radian Angle: (π / 180) × 90 = 1.5708 rad
  • Bend Allowance (BA): 1.5708 × 3.80 = 5.969 mm
💡 Air Bending Natural Radius Rule: In standard air bending of mild steel, the naturally formed inside radius is approximately 16% of the lower V-die opening width (R ≈ 0.16 × V).
⚠️ K-Factor Limits: K-factor can never mathematically exceed 0.50 (the elastic centerline) or drop below 0.25 (extreme tight coining limit). Most precision CNC air bending sits between 0.38 and 0.45.

Frequently Asked Questions (FAQ)

What is the difference between Bend Allowance and Bend Deduction?

Bend Allowance is the arc length of the curved neutral axis—you add it to the straight tangent leg segments. Bend Deduction is the amount of material you subtract from the sum of outside mold flange dimensions (apex-to-edge).

Why does the neutral axis shift during bending?

As bending proceeds past the elastic yield point, compressive stress on the inside surface causes localized cross-sectional thinning and strain hardening, forcing the zero-stress neutral fiber to migrate toward the inside radius.

When should I use Bend Allowance over Bend Deduction?

Bend Allowance is ideal when drawing dimensions are measured along inside flat surfaces or tangent lines. Bend Deduction is preferred when prints are dimensioned to outside mold lines or virtual sharp apex corners.

Engineering Disclaimer: Bend allowance calculations are theoretical engineering models. Machine rigidity, tooling friction, rolling grain direction, and material heat lot ductility variations can affect final bent dimensions. Calibrate with physical coupon testing for high-precision fabrications.